10 Mistaken Answers To Common Audi G28 Questions Do You Know The Right…
페이지 정보
작성자Enrique 댓글댓글 0건 조회조회 16회 작성일 24-10-17 05:02본문
How to Replace an audi car key G28 Engine Speed Sensor
In this video, Charles the Humble Mechanic shows how to replace the G28 engine speed sensor. The sensor is located at the edge of transmission over the flywheel gear. It sends a message to the ECU via a grey wire T55/49, then to the tachometer in the instrument cluster.
1. Engine Speed Sensor
It is located on the outside of the transmission above the flywheel ring gear the G28 Engine Speed Sensor sends signals to ECU pin T55/49 via the grey wire. The ECU then utilizes this information to regulate fuel, timig and boost. It also sends signals to the G5 tachometer inside the instrument cluster.
The sensor serves as a reference to correlate with the G40 Camshaft Position Sensor. The ecu has to be aware of when the crankshaft has reached TDC and also the location of the camshaft in order to activate the spark and injectors.
If this sensor fails to function, the ECU will display a P00160 error message. This means that the Crank Shaft is out of sync with the Intake Camshaft. It could also be a sign of the possibility of a chain stretch or jumped chain link in the upper chain of timing. However, the error code won't appear on its own without additional information from other sensors (G4 and G40).
Testing is a bit tricky because there are two connector pins and they serve different purposes however the best method to test it is to measure resistance between the sensor and the ECU. It should read approximately 1000 ohms when it is operating at its maximum. If you're experiencing issues with this part, check for signs of oil or coolant in the connector bay.
2. Injectors
Yesterday, while accelerating at full speed from the highway paytoll, i experienced massive power loss as if the engine was running out of gas or injectors aren't firing anymore. In the morning, i removed the spark plugs. Three were drenched in gazoline, the 4th one was dry. When I crank the engine with no sparks i put tissue on the top of each of the injector holes and the 3 drenched with gazoline jump out but the 4th stay shut. I checked the ground connection of ECU pins 14,30 and 48/55. I found zero ohm. So i assume the problem is elsewhere.
I also tried to reset the PID but with no luck. The car will start when the G28 is unplugged, and it works fine when the G28 connected. However the intermittent misfire issue still occurs at higher RPM. The temperature sensor for coolant (G62) shows the wrong temperature of -49c, even if I unplug it. I also noticed that the oil gauge in the cockpit shows 2 bars when the actual pressure is zero.
I don't know what to do. I think I've eliminated everything else. However, i'm afraid that I might have missed something. If anyone has any suggestions, please let me know! TIA!
3. Fuel Pump
The fuel pump of the g28 gets a signal from the RPM sensor. The GM-style sender is the same as the G4 and they both work in the 80 100 200, UrS and RS2 cars so you can easily find one at a salvage yard or at a parts store. Test them out - put your DMM in resistance mode and take measurements between pins 1 (with the bump on the connector's end up) and 2 (2nd from the left on the black connector's end). They should be infinite ohms.
4. ECU
Our 20vt turbo (3B AAN, ABY, and ADU) engines are equipped with an ECU that has to be aware of the speed and position of the crankshaft in order to make a decision about timing of the fuel injector, for example. In order to do this it utilizes a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If either of these sensors go wrong, you will receive codes on the diagnostic scanner which could cause engine shut down.
A failing G28 sensor could result in an inaccurate speed counter for the gearbox, replacement audi key cost replacement audi a3 key key - https://telegra.ph/ - a gearbox that shifts more quickly than normal, and/or an unfire when in gear. It is probable that the sensor is failing and needs to be replaced if you encounter any of these signs. The good news is that they are very cheap and easy to find, especially if you're looking at the Bosch sensor, which is what we have. If you prefer, GM's version of this part is a good option.
5. Tachometer
A malfunctioning engine sensor can cause a variety of issues in your vehicle. It is an important part of the transmission in your audi a1 key fob since it sends information to the ECU regarding how fast or slow the engine of the car is spinning. This sensor could cause the transmission to malfunction and other components of the car to be affected.
The G5 engine speed sensor is situated on the edge of the transmission above the flywheel ring gear and sends a signal to the ECU at pin T55/49 via a grey wire. The ECU then processes this signal to control fuel, timig and boost and then transmitting it to the G5 tachometer inside the instrument cluster. You can test the sensor for failure by checking continuity between it and the tachometer, between ECU pin T55/49 and the instrument cluster connection to pin T6a/1 (trace [79trace [79]) and between T6a/1 and the instrument cluster pin T26a/12. It should show approximately 1000 ohms of resistance between those two pins. This is a standard part across the audi key replacement cost 80, 100 200, UrS and RS2 range from 1985 MC until the 1997 UrS AAN and 1995 RS2 ADU so good ones might be availble in wrecking yards.
In this video, Charles the Humble Mechanic shows how to replace the G28 engine speed sensor. The sensor is located at the edge of transmission over the flywheel gear. It sends a message to the ECU via a grey wire T55/49, then to the tachometer in the instrument cluster.
1. Engine Speed Sensor
It is located on the outside of the transmission above the flywheel ring gear the G28 Engine Speed Sensor sends signals to ECU pin T55/49 via the grey wire. The ECU then utilizes this information to regulate fuel, timig and boost. It also sends signals to the G5 tachometer inside the instrument cluster.
The sensor serves as a reference to correlate with the G40 Camshaft Position Sensor. The ecu has to be aware of when the crankshaft has reached TDC and also the location of the camshaft in order to activate the spark and injectors.
If this sensor fails to function, the ECU will display a P00160 error message. This means that the Crank Shaft is out of sync with the Intake Camshaft. It could also be a sign of the possibility of a chain stretch or jumped chain link in the upper chain of timing. However, the error code won't appear on its own without additional information from other sensors (G4 and G40).
Testing is a bit tricky because there are two connector pins and they serve different purposes however the best method to test it is to measure resistance between the sensor and the ECU. It should read approximately 1000 ohms when it is operating at its maximum. If you're experiencing issues with this part, check for signs of oil or coolant in the connector bay.
2. Injectors
Yesterday, while accelerating at full speed from the highway paytoll, i experienced massive power loss as if the engine was running out of gas or injectors aren't firing anymore. In the morning, i removed the spark plugs. Three were drenched in gazoline, the 4th one was dry. When I crank the engine with no sparks i put tissue on the top of each of the injector holes and the 3 drenched with gazoline jump out but the 4th stay shut. I checked the ground connection of ECU pins 14,30 and 48/55. I found zero ohm. So i assume the problem is elsewhere.
I also tried to reset the PID but with no luck. The car will start when the G28 is unplugged, and it works fine when the G28 connected. However the intermittent misfire issue still occurs at higher RPM. The temperature sensor for coolant (G62) shows the wrong temperature of -49c, even if I unplug it. I also noticed that the oil gauge in the cockpit shows 2 bars when the actual pressure is zero.
I don't know what to do. I think I've eliminated everything else. However, i'm afraid that I might have missed something. If anyone has any suggestions, please let me know! TIA!
3. Fuel Pump
The fuel pump of the g28 gets a signal from the RPM sensor. The GM-style sender is the same as the G4 and they both work in the 80 100 200, UrS and RS2 cars so you can easily find one at a salvage yard or at a parts store. Test them out - put your DMM in resistance mode and take measurements between pins 1 (with the bump on the connector's end up) and 2 (2nd from the left on the black connector's end). They should be infinite ohms.
4. ECU
Our 20vt turbo (3B AAN, ABY, and ADU) engines are equipped with an ECU that has to be aware of the speed and position of the crankshaft in order to make a decision about timing of the fuel injector, for example. In order to do this it utilizes a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If either of these sensors go wrong, you will receive codes on the diagnostic scanner which could cause engine shut down.
A failing G28 sensor could result in an inaccurate speed counter for the gearbox, replacement audi key cost replacement audi a3 key key - https://telegra.ph/ - a gearbox that shifts more quickly than normal, and/or an unfire when in gear. It is probable that the sensor is failing and needs to be replaced if you encounter any of these signs. The good news is that they are very cheap and easy to find, especially if you're looking at the Bosch sensor, which is what we have. If you prefer, GM's version of this part is a good option.
5. Tachometer
A malfunctioning engine sensor can cause a variety of issues in your vehicle. It is an important part of the transmission in your audi a1 key fob since it sends information to the ECU regarding how fast or slow the engine of the car is spinning. This sensor could cause the transmission to malfunction and other components of the car to be affected.
The G5 engine speed sensor is situated on the edge of the transmission above the flywheel ring gear and sends a signal to the ECU at pin T55/49 via a grey wire. The ECU then processes this signal to control fuel, timig and boost and then transmitting it to the G5 tachometer inside the instrument cluster. You can test the sensor for failure by checking continuity between it and the tachometer, between ECU pin T55/49 and the instrument cluster connection to pin T6a/1 (trace [79trace [79]) and between T6a/1 and the instrument cluster pin T26a/12. It should show approximately 1000 ohms of resistance between those two pins. This is a standard part across the audi key replacement cost 80, 100 200, UrS and RS2 range from 1985 MC until the 1997 UrS AAN and 1995 RS2 ADU so good ones might be availble in wrecking yards.댓글목록
등록된 댓글이 없습니다.
